|
|
- 10/100Base-T Auto-Negotiating
- Distances up to 100km
- 2-Way "One Fiber" Communication
Optional
- Multimode & Single Mode
(1300/1550nm)
-
Hardened Temperature (-40°C
to 80°C) Optional, Exceeds NEMA & Caltrans Traffic Control
Specs
- Five Diagnostic LED Indicators
- Built-In Power Redundancy
- Local Dry Contact Alarm Relay
- Rackmount or Stand Alone
|
|
Datasheet
TC3210S
Standalone/Wallmount
.jpg)
TC3210S
Standalone/Wallmount (Single Optic)
(Click on images to enlarge)
|
Applications
The TC3210R/S is typically used to
interconnect 10/100Mbps switching hubs, workstations or any other Fast
Ethernet compliant device at distances up to 100km.
appdiagram.gif)
Top
Description
Featuring connectivity distances up to
100km, the TC3210R/S Media Converter converts or connects 10/100Mbps
Ethernet Unshielded Twisted Pair (10/100Base-T) to single mode or
multimode fiber optics (10/100Base-FX). It is commonly used to
interconnect network bridges, hubs, or workstation cards. The TC3210S is the standalone/wallmount unit.
The TC3210R rackmount version fits into TCRM192
or TCRM196 19" rackmount card cages.
Completely transparent to the network, the
TC3210R/S is ideal for integrating UTP and fiber optics in any Fast
Ethernet network. Designed with modern Field Programmable Gate Array
(FPGA) technology, it operates efficiently even during high-demand traffic
loads.
Dry contact alarms are provided for connection to remote network
management systems. A local fiber loopback feature, eight LED indicators, and an
Uplink/Downlink slide switch are provided on the front panel to assist in
installation & troubleshooting.
The TC3210R/S is available both multimode (1300nm) and single mode (1300nm
& 1550nm). Fiber optic connectors are ST or FC. The UTP connector is
RJ-45 female. Power is 12VDC @ 600mA (standard); optional power sources
include 24VDC, -48VDC, 125VDC, or 115/230VAC with an external power cube. An
extreme temperature version (-20° to 70°C, -40° to 80°C), Model TC3210X, is also
available.
A terminal block connector on the rear panel provides for the dry contact
relay alarm. Normally in the OPEN position, any loss of electrical or
optical signal will trigger an alarm condition and force the switch to the
CLOSED position. This relay can be used in conjunction with an external
device to monitor the condition of the link.
Top
Technical
Specifications
| Data
Rate |
|
10/100 Mbps (Auto-Sensing) |
| Optical |
| Interface |
100Base-FX |
| Transmitter |
ELED, LASER* |
| Receiver |
PIN
Diode |
| Wavelength |
1300nm Multimode
1300nm, 1550nm Single Mode |
| Fiber
Optic Connectors |
ST,FC
or SC |
Loss
Budget*
(1300nm, 1550nm) |
Multimode
(62.5/125µm): 15dB
Single Mode (9/125µm): 20dB |
| Electrical |
| Interface |
10/100Base-T Ethernet |
| Connector |
(UTP)
RJ45 Female |
| System
|
| Bit
Error Rate |
1
in 109
or better |
* Contact factory for higher requirements
|
|
| ALARM |
| Dry
Contact |
Normal
OPEN |
| Visual
Indicators |
| Power
Status |
PWRA,
PWRB, Vcc |
| UTP
Signal Status |
Auto Neg. Detect, TP, 10M, 100M |
| Optic
Signal Status |
FO, 10M, 100M |
| Power |
| Standard |
12VDC
@ 600 mA |
| Optional |
24VDC, -48VDC, 125VDC, 115/230VAC (with external power cube) |
|
Temperature
|
| Operating |
0° to
50°C |
| Hi-Temp
(optional) |
-20° to 70°C |
|
Extreme Temp (optional) |
-40° to
80°C |
| Storage |
-40° to 90°C |
| Humidity |
95% non-condensing |
| Physical
(Wallmount Base Unit)
(Details) |
| Height |
(3.53
cm) 1.39" |
| Width |
(18.13
cm) 7.1" |
| Depth |
(16.59
cm) 6.53" |
| Weight |
(501
gm) 1.1 lbs. |
|
|
Top
©
2007, TC Communications, Inc. All
rights reserved.
17881 Cartwright Road - Irvine, CA 92614, info@tccomm.com
Tel:(949)852-1972, Sales:(800)569-4736
Fax:(949)852-1948, sales@tccomm.com
|
Page Last Updated:
05/21/2008
|
|
